BANLI HARDWARE SDN BHD

Excellent glossy-mirror like, recommended for interior wood & metal surface.

品质优越，光泽夺目的光面漆，适用于室内各种木质和金属表面。

Steps:​

1. Stir well,  the mild steel must be free from dirt / rust before painting. If necessary, use 5 - 10% thinner & stir well.

(WOOD SURFACE)

1. Coats 1 layer of KTH White undercoat
   涂上一层 KTH White Undercoat

2. Coats 2 layer of KTH High Gloss Paint 5953
   涂上两层 KTH High Gloss Paint 5953

(METAL SURFACE)

1. Coats 1 layer of KTH Zinc Chromate Grey Green / KTH Red Oxide Primer
   涂上一层 KTH Zinc Chromate Grey Green 或 KTH Red Oxide Primer

2. Coats 1 layer of KTH White undercoat
   涂上一层 KTH White Undercoat

3. Coats 2 layer of KTH High Gloss Paint 5953. 涂上两层 KTH High Gloss Paint 5953

Non pigmented clear coating, are applied to the surfaces dry and smooth film.

不含颜料的透明涂料，涂施与物体表面干结光滑的薄膜。

Steps:​

1. The mild steel substrate must be completely dry and free from rust, mill scale, dirt, grease and other contaminants before painting. 确保表面干爽清洁，无油迹、生锈、氧化皮、污垢和其他杂质。

2.  Stir thoroughly before use. Product is supply ready for use. However, if thinning is required, not more than 10% turpentine may be added.使用前搅拌均匀。马上可使用，如要较稀的漆可加入不超过10%的叻水。

​

​

Rapid drying finish with outstanding resistance to serve weathering  gloss retention, good flow & leveling properties. 一种快干的聚氨酯配方，它拥有良好的耐热气候及持久性高光泽和刘平性能。适用于重轻工业用途。

Steps:​

1. The surface to be coated should be clean, sound and dry prior to paint application. 在尚未油漆前，先清除表面使之清洁，完美及干燥

2. Stir thoroughly before use. Product is all ready for use.使用前搅拌均匀。马上可使用。

Water-borne sealer for interior & exterior walls. It is formulated with special acrylic polymer for excellent efflorescence resistant, alkaline resistant, good adhesion & excellent anti-fungus & algae property.

适用于内墙和外墙的水性底漆, 具有出色的抗风化性。 它具有优异的耐碱性，良好的粘附性能和优异的抗真菌和藻类抗性。

Steps:​​

(NEW MANSORY SURFACE)

1. allow wall to dry out thoroughly. Remove dirt, dust, grease and other contaminants before painting. 确保墙壁彻底干燥, 涂漆前清除污垢, 灰尘, 油脂和其他污染物.

(PREVIOUSLY PAINTED SURFACE)

1. Remove unstable paint film, grease, etc. Leave it overnight & wash with clean water. Dry the surface thoroughly before painting.去除所有松散的材料，不稳定的漆膜，油脂等。将其放置过夜，然后用清水洗净。 涂漆前彻底擦干表面。

Excellent protection against fresh & salt water, abrasion, chemical and resistant to crude & heavy oils.

具有优良的防淡水和咸水, 耐磨性, 耐化学性和耐粗和重质油。

Steps:​

​(CONCRETE SURFACE)

1. Remove previous coating / chalk with sulphuric acid. Then, rinse with clean water & allow it to dry completely.

(STEEL SURFACE)

1. Mild steel substrate must be dry & free from rust, dirt or other stain before painting. Bare metals should be sanded properly for better effect.

(Aluminium & Galvanised Iron Surface)

1. Remove oil, grease and dirt by using solvent or other cleaning chemicals.

***Ratio for volume of Epoxy Finish to  Hardener is 4:1. Stir the content of epoxy & gradually add hardener until a homogeneous mix is obtained. If thinning is required, not more than 10% of thinner should be added.

Has antifungus/algae formula to protect   slates, bricks, quarry / porous tiles, natural stone, cementitious substrate etc against staining, efflorescence, scratching, fungus& algae. Suitable apply on exterior & interior usage on concrete, wood and metal.

100%亚克力油性配方制成，附加防青苔用在用於石板，砖块，瓷砖，石头及石灰地。

Steps:​

1. The surface to be coated should be clean, sound and dry prior to paint application.在尚未油漆前，先清除表面使之清洁，完美及干燥。

2. Stir thoroughly before use. Product is  ready for use. 使用前搅拌均匀, 马上可使用。

Suitable for interior & exterior surfaces with high temperature for up to 200°C, 300°C, 600°C. It produces brilliant luster & reduces temperature by reflecting solar heat.

适合于内部和外部表面, 符合高温至200℃,  300℃, 600℃. 它是具有反射太阳热量的产品。

Steps:​

1. Surface must be dry and free from dirt, grease and other contaminants. Clean off dust and dry, ferrous substrate should be sanded or wire-brushed to remove mill scales and rust. 表面必须干燥，无污垢，油脂及其他杂质。擦去灰尘和干燥，使用砂纸或钢丝刷掉任何铁锈斑点白垩和旧漆。

2. If thinning is required, not more than 5% turpentine may be added.马上可使用，如要较稀的漆可加入不超过5%的叻水。